美國進口EXTEC品牌Labcut 250B型臺式金剛砂切割機

●一般特點：

1)臺式，手動操作，切割飛輪直徑zui大為10 inch (254mm)，可用于切割以下材料：

硬質鋼；工具鋼；鑄鐵；鋼和鎳合金；

非鐵金屬，如鋁、銅、鈦等；

陶瓷；玻璃；復合材料；

硬金屬如碳鋼；

也可切割桿條和管子；

2)金剛砂飛輪間接地由3相4 HP (3 KW)馬達驅動，轉速為3900rpm?？蛇x配滑車和皮帶裝置來改變切割速度。為了提升或降低切割頭，1個探位器被放在蓋子的一邊。1個制動缸與升降探位器配合，因此切割非常好控制；

3)該機器床為T型槽基座，由虎頭鉗固定。標準儀器提供左、右邊的快速虎頭鉗，容量為2 ? inch (64mm)。樣品材料的兩邊被夾子緊緊夾住以確保zui小的毛刺。非常長的樣品，可通過兩邊的頂蓋的孔輕松操作；

4)1個17 L的55L/min的泵循環將液體送到旋轉飛輪的兩邊，并流經工作區域。如果須要干式的切割，則可停止制冷循環。該制冷循環也可用作清洗功能。在儀器的前面進行操作控制；

5)在控制板后面的櫥柜里放有電子元件。前面面板通過24V回路控制，滿足嚴格的安全要求。前面面板上有切割頭馬達開/關，制冷泵開/關，內部燈光開關。該儀器設計時已考慮操作者的安全。1個定時安全開關能在切割飛輪仍在旋轉時防止蓋子打開；

●技術特點：

1)馬達：4 HP (3KW) 3相馬達；

2)主軸直徑：zui大為1 1/4 inch (32mm)；

3)飛輪轉速：標準3900 rpm；

4)飛輪尺寸：zui大直徑為10 inch (254mm)，也可放小的飛輪；

5)尺寸WDH：512×685×620 mm；

6)重量：80Kg；

●訂購信息：

10250： Labcut 250B型臺式金剛砂切割機，包括再循環系統(10312)、左(10256)、右(10257)的快速虎頭鉗；

10256：左邊的快速虎頭鉗；

10257：右邊的快速虎頭鉗；

10312：再循環槽系統；

10251：250F型立式金剛砂切割機(包括10250和10258)；

10258：支持架，用于Labcut 250B；

Extec's Labcut 250B is a bench-top, manually operated abrasive cutting machine designed for cutting wheels up to 10 inch (254mm) diameter. The Labcut 250B can be used to section a wide variety of modern materials including:

• Hard Steels
• Tool Steels
• Cast Iron
• Steel and Nickel Alloys
• Non-ferrous Metals eg. Aluminum, Brass, Titanium
• Ceramics
• Glass
• Composite Materials
• Hard metals e.g. Carbides
• The Labcut 250 also cuts bar and tube

The abrasive cutting wheel is indirectly driven at 3900 rpm using a 3-phase 4 HP (3 kW) motor. An optional pulley and belt set is available for changing cutting speeds. To raise and lower the cutting head, a lever is located at the side of the canopy. A hydrocheck is fitted to the raise/lower lever so that cutting can be carried out in a smooth manner.

The machine bed is a T-slot base on which the vises are mounted. The standard machine is supplied with right hand and left hand quick action vises having 2 ½ inch (64mm) capacity. The material is clamped on either side of the cut ensuring minimum burr. Long lengths of material can be easily handled using access ports on both sides of the canopy.

A 4.4-gallon (17 l) with 55-liter/min pump circulates fluid on both sides of the rotating wheel and floods the work area. If dry cutting is required, the coolant circulation can be stopped. The coolant circulation system can also be used as a wash down facility; suitable controls for this are located on the front panel.

The electrical components are housed in a closed cabinet located behind the control panel. The front panel switching is via 24 V control circuits and therefore complies with even the most rigorous safety codes. Front panel controls include cutting head motor on/off , coolant pump on/off and internal light switch. The Labcut 250B has been designed with operator safety in mind. A timed safety switch prevents the canopy from being opened while the cutting wheel is rotating.

• Motor:
  • 4 HP (3kW) 3 Phase Motor - specify voltage
• Spindle Diameter:
  • Maximum 1 1/4 inch (32mm) diameter
• Wheel Speed:
  • Standard 3900 rpm
• Wheel Size:
  • 10 inch (254mm) maximum (smaller diameter wheels can be fitted
• Dimensions:
  • Width: 20.2" (512mm)
  • Depth: 27"(685mm)
  • Height: 24.4" (620mm)
• Weight:
  • 176 lbs. (80kg)